The Tazer JL Mini Programmer from Z Automotive is an essential tool for all Jeep Wrangler or Gladiator owners. This small device offers a lot of features, intuitive navigation, provides full control over basic and additional vehicle features, so you can fully personalize your Jeep's equipment and performance.
The module supports all engine versions regardless of the type of transmission used, including export models. Simple plug-and-play installation: detach the SGW module, which is located above the OBD2 diagnostic connector, and connect the Tazer JL Mini in its place. All functions can be accessed via a display on the dashboard, and changed using buttons on the steering wheel.
Specs:
Changing vehicle settings permanently - changes made to the vehicle, will work even when the programmer is disconnected
Changing vehicle settings live - changes are made live in real time and only work if the programmer is connected to the vehicle
“Non-Menu” Live Functions are operations the Tazer Ram performs live, only while it is physically connected, and are not located in a menu. They are activated automatically or with button presses.
List of vehicle settings (engine off):
Light show – 6 pre-programmed and 3 custom light shows that flash all exterior lights - ideal for car shows/first responders/off-road visibility – controlled from remote control (key fob) or steering wheel buttons -can be turned on in motion for use in parades or off-road
Change tire size
Change gear ratio (max 4.50 on 4XE)
Change transfer case LOW ratio
Enable/disable TPMS warnings (Tire Pressure Monitoring System)
Set TPMS pressure warning limit, front and rear, between 25psi/1.7bar and 85psi/5.8bar
Enable/disable backup camera
Enable/disable Cargo Camera input (8.4 UConnect only)
Enable/disable TravelLink/XM Traffic and weather
Activate Offroad Pages (after upgrade to 8.4” radio)
Change Daytime Running Lights (DRL) location
Enable/disable DRL Dropout (DRL turn off while using blinker)
Enable/disable factory fog lights
Enable/disable Fog Light Dropout (when fogs shut off while using high beams)
Enable/disable one-touch lane change
Enable/disable factory halo lights
Change headlight type (Std/LED)
Change fog light type (Std/LED)
Change tail light type (Std/LED)/delete sensor circuit for aftermarket lights
Change front turn signal (std/LED)/delete sensor circuit for aftermarket lights
Enable/disable factory auto hi-beam
Enable/disable Trailer Tow setting
Disable electronic sway bar (if removed from the vehicle)
Disable electronic steering pump (after hydraulic steering conversions)
Enable the trailer brake controller (primarily Gladiator)
Disable front and rear lockers for axle swaps
Disable front axle disconnect module for axle swaps
Declare the presence of a Drivetrain Control Module (Rubicon Transfer Case)
Enable/disable Aux Buttons
Enable/disable Blind Spot Detection
Delete the seat belt reminder chime
Enable/disable/change ParkSense configuration
Change cluster splash screen
Enable HVAC dual-zone switch assembly when upgrading from 5” radio
Enable HomeLink (if HomeLink visor and harness are installed)
Enable/disable auto dimming mirror (if installed)
Enable Proximity Entry (if handles and harnesses are installed)
Enable pickup bed outlet (Gladiator)
Enable/disable auto headlights after sensors are installed
Enable/disable PANIC button on remote
“Unmarry” function returns to stock
List of Live Functions (engine on):
Activate Light Show
Hold brakes at red light (excluding 4XE)Use Garage Door Opener after shutdown
Enable navigation entry in-motion
TurnCAM – activate backup camera while using turn signals (5”, 7” and 8.4” UConnect)
Kill3Honk – deactivate three honks after leaving running vehicle
Toggle hood alarm
Enable passenger side heat on remote start
Flash third brake light when braking
Customize third brake light flash pattern
Define Winch Mode RPM between 1250 and 2000 RPM (excl. 4XE)
Flash lights to indicate tire pressure while filling
Dark Mode – turn off all exterior and interior lighting while parked with the engine running
Activate and cycle through camera inputs
Display Vacuum/Boost Gauge
Activate 0-30 timer and 0-60 timer
Force RWD (392 only)
Display firmware version
“Non-Menu” Live Functions:
AutoStopStart disable – Tazer JL Mini will remember your last settings
AutoTracKill – Tazer JL Mini will remember your last TC settings
Disconnect sway bar in 2WD up to 30mph or at any speed if mapped to a button
License Plate Blanking (Gladiator) – automatically turn off license plate light when in reverse or using TurnCam to reduce glare
Light Show (shortcut)
Open windows using keyfob (experimental, may not work with all bypass types)
Line Lock – lock front brakes for easy burnout
Disable ESP/TC by holding ESP button
Cycle camera outputs (shortcut)
Cooldown Mode – turn on engine fans, even when engine is off
Winch Mode – raise idle RPM to selected value
Partial Reboot
Remarks:
Can be used with one car only (lock)
